Plumbing for Beginners: What You Need for Bathtub Installation
Plumbing for Beginners: What You Need for Bathtub Installation
Blog Article
We've come across this post relating to How to Install a Bathtub directly below on the net and figured it made good sense to talk about it with you over here.
Setting up a bathtub isn't specifically brain surgery, however it does require strong plumbing, carpentry, and occasionally, tiling skills. Replacing an old tub with a new one is also a reasonably challenging task. If the old bathtub is easily obtainable, the job can move easily; if you need to open up a wall to get rid of the old tub and position the brand-new bathtub, the task is a lot harder. In either situation, the task is within a home handyman's skills, although you will require a helper to move out the old bathtub as well as embeded in the brand-new one. Ensure you have actually certified on your own for the job and are comfortable attempting it. Instead of working with a professional to take over a halfway-completed job, it is much better to take into consideration utilizing one prior to you begin. Possibilities are you may need a specialist plumber to make tube links.
This post will help you install a brand-new tub in your bathroom if you have currently gotten a new bathtub and don't require to change the plan of your previous water system pipes.
Your tools and material checklist need to comprise the following:
Planning for the Installment
To start with, the sustaining framework supplied with the bath ought to be fitted (if called for) according to the manufacturer's directions. Next, fit the faucets or mixer to the bath tub. When fitting the tap block, it is very important to make sure that if the tap comes with a plastic washer, it is fitted between the bath as well as the taps. On a plastic bath, it is likewise practical to fit a supporting plate under the taps unit to prevent strain on the bath tub.
Fit the adaptable faucet ports to the bottom of the two taps making use of 2 nuts and also olives (occasionally provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and after that pass the outlet through the hole in the bathroom. Make use of the nut provided by the producer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the adaptable overflow pipeline to the overflow outlet. Afterwards, screw the pipeline to the overflow face which must be fitted inside the bathroom. See to it you make use of every one of the provided washing machines.
Link the catch to the bottom of the waste outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Attach the bottom of the overflow tube in a similar manner.The bath must currently prepare to be suited its last placement.
Removing Old Touches
If you require to change old faucets with brand-new ones as a part of your installment, after that the first thing you need to do is separate the water system. After doing so, activate the faucets to drain any type of water continuing to be in the system. The procedure of getting rid of the existing faucets can be rather troublesome due to the restricted accessibility that is commonly the case.
Utilize a container wrench (crowsfoot spanner) or a tap device to reverse the nut that links the supply pipes to the taps. Have a towel all set for the remaining water that will certainly come from the pipes. Once the supply pipelines have been eliminated, utilize the same device to loosen up the nut that holds the taps onto the bath/basin. You will certainly require to quit the single taps from turning during this process. As soon as the faucets have been eliminated, the holes in the bath/basin will certainly have to be cleaned up of any kind of old securing substance.
Before proceeding to fit the brand-new faucets, contrast the pipeline links on the old faucets to the brand-new faucets. If the old faucets are longer than the brand-new taps, then a shank adapter is required for the brand-new faucets to fit.
Installing the Bathtub
Using the two wood boards under its feet, place the bathtub in the required placement. The wood boards are handy in equally spreading out the weight of the tub over the area of the boards rather than focusing all the weight onto 4 little factors.
The following goal is to make certain that the bath tub is leveled all round. This can be accomplished by inspecting the level as well as changing the feet on the tub until the level reviews degree.
To mount faucets, fit all-time low of the furthest adaptable tap adapter to the appropriate supply pipe by making a compression join; then do the very same for the other faucet.
Switch on the water system and examine all joints and new pipework for leakages and also tighten them if required. Load the bath tub and likewise inspect the overflow electrical outlet and also the regular outlet for leaks.
Finally, repair the bath paneling as explained in the maker's user's manual. Tiling and also sealing around the bathtub should wait until the bathtub has actually been made use of at the very least when as this will certainly settle it into its last placement.
Suitable New Touches
If the tails of the new taps are plastic, after that you will certainly need a plastic adapter to stop damage to the thread. One end of the adapter fits on the plastic tail of the tap and the various other end offers a connection to the existing supply pipes.
If you require to fit a monobloc, then you will certainly call for decreasing couplers, which attaches the 10mm pipeline of the monobloc to the basic 15mm supply pipe.
Next, place the faucet in the installing hole in the bath/basin ensuring that the washers remain in area between the faucet and also the sink. Secure the faucet in place with the supplier given backnut. When the faucet is firmly in position, the supply pipelines can be attached to the tails of the taps. The faucets can either be attached by utilizing corrugated copper piping or with regular tap connectors. The former kind must be linked to the tap finishes initially, tightening just by hand. The supply pipelines can later be attached to the other end. Tighten both ends with a spanner after both ends have actually been connected.
Tiling Around the Tub
In the location where the bathroom fulfills the ceramic tile, it is needed to secure the joins with a silicone rubber caulking. This is necessary as the installation can move sufficient to split an inflexible seal, triggering the water to permeate the wall surface between the bathroom and also the tiling, causing issues with moisture and possible leakages to the ceiling below.
You can pick from a selection of coloured sealants to assimilate your fixtures and fittings. They are marketed in tubes and cartridges, as well as can securing gaps approximately a size of 3mm (1/8 inch). If you have a larger space to fill up, you can load it with twists of soaked newspaper or soft rope. Keep in mind to always fill the tub with water prior to securing, to permit the movement experienced when the tub is in use. The sealant can break relatively early if you do not take into consideration this activity prior to securing.
Additionally, ceramic coving or quadrant ceramic tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are also conveniently readily available on the marketplace. It is recommended to fit the ceramic tiles making use of waterproof or water resistant sticky and also grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Do you appreciate reading about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround? Try leaving a remark down below. We will be glad to find out your thoughts about this write up. We hope that you come back again later on. Sharing is nice. Who knows, you will be doing someone a favor. Many thanks for your time invested reading it.
Burst? Reach us! Report this page